Directories
¶
| Path | Synopsis |
|---|---|
|
board
|
|
|
examples
|
|
|
ads1115
command
Ads1115 demonstrates how to communicate with the ADS111x ADC using the low-level I2C interface.
|
Ads1115 demonstrates how to communicate with the ADS111x ADC using the low-level I2C interface. |
|
blinky
command
Blinky flashes the on-board LED.
|
Blinky flashes the on-board LED. |
|
blinky1
command
Blinky flashes the on-board LED.
|
Blinky flashes the on-board LED. |
|
crudeblinky
command
Crudeblinky flashes the on-board LED without using HAL.
|
Crudeblinky flashes the on-board LED without using HAL. |
|
cytron-maker
command
|
|
|
display
command
Display draws on the connected display.
|
Display draws on the connected display. |
|
displayi2c
command
|
|
|
dma
command
Dma shows how to use the DMA controller for RAM to RAM transfers.
|
Dma shows how to use the DMA controller for RAM to RAM transfers. |
|
eeprom
command
|
|
|
eepromll
command
|
|
|
gpiotest
command
Gpiotest tests all GPIOs exposed as the Pico 2 GPIO pins.
|
Gpiotest tests all GPIOs exposed as the Pico 2 GPIO pins. |
|
irqpin
command
Irqpin shows how to setup an IO pin to be an interrupt source.
|
Irqpin shows how to setup an IO pin to be an interrupt source. |
|
pcf8574
command
Pcf8574 writes consecutive numbers to the remote I/O expander chip (PCF8574) using I2C protocol.
|
Pcf8574 writes consecutive numbers to the remote I/O expander chip (PCF8574) using I2C protocol. |
|
readpin
command
Readpin polls the state of the GP15 pin and shows it using the onboard LED.
|
Readpin polls the state of the GP15 pin and shows it using the onboard LED. |
|
smpblinky
command
Smpblinky tests the Go and noos schedulers.
|
Smpblinky tests the Go and noos schedulers. |
|
spi
command
SPI loop test: wire GP3 and GP4 together.
|
SPI loop test: wire GP3 and GP4 together. |
|
spotpear-pico-1.54inch-lcd
command
Pico-lcd-1.54inch-lcd allow to test the onboar buttons.
|
Pico-lcd-1.54inch-lcd allow to test the onboar buttons. |
|
uart
command
Uart allows to tests the communication over UART peripheral.
|
Uart allows to tests the communication over UART peripheral. |
|
w5500
command
W5500 tests the communication with the WIZnet W5500 TCP/IP Ethernet controller.
|
W5500 tests the communication with the WIZnet W5500 TCP/IP Ethernet controller. |
|
waveshare-pico-8seg-led
command
Pico-8seg-led uses standard fmt.Fprintf function to prints different chars and numbers on the 8-segment display.
|
Pico-8seg-led uses standard fmt.Fprintf function to prints different chars and numbers on the 8-segment display. |
|
waveshare-pico-lcd-1.3
command
Pico-lcd-1.3 is similar to the Waveshare demo code for this module.
|
Pico-lcd-1.3 is similar to the Waveshare demo code for this module. |
|
waveshare-pico-restouch-lcd-2.8
command
Pico-restouch-lcd-2.8 allows to test the LCD module.
|
Pico-restouch-lcd-2.8 allows to test the LCD module. |
|
ws2812
command
WS2812 uses the UART peripheral to drive the string of the WS2812 RGB LEDs.
|
WS2812 uses the UART peripheral to drive the string of the WS2812 RGB LEDs. |
|
module
|
|
Click to show internal directories.
Click to hide internal directories.