cisco_telemetry_gnmi

Cisco GNMI Telemetry

Cisco GNMI Telemetry is an input plugin that consumes telemetry data based on the GNMI Subscribe method. TLS is supported for authentication and encryption.

It has been optimized to support GNMI telemetry as produced by Cisco IOS XR (64-bit) version 6.5.1, Cisco NX-OS 9.3 and Cisco IOS XE 16.12 and later.

Configuration

[[inputs.cisco_telemetry_gnmi]]
  ## Address and port of the GNMI GRPC server
  addresses = ["10.49.234.114:57777"]

  ## define credentials
  username = "cisco"
  password = "cisco"

  ## GNMI encoding requested (one of: "proto", "json", "json_ietf")
  # encoding = "proto"

  ## redial in case of failures after
  redial = "10s"

  ## enable client-side TLS and define CA to authenticate the device
  # enable_tls = true
  # tls_ca = "/etc/telegraf/ca.pem"
  # insecure_skip_verify = true

  ## define client-side TLS certificate & key to authenticate to the device
  # tls_cert = "/etc/telegraf/cert.pem"
  # tls_key = "/etc/telegraf/key.pem"

  ## GNMI subscription prefix (optional, can usually be left empty)
  ## See: https://github.com/openconfig/reference/blob/master/rpc/gnmi/gnmi-specification.md#222-paths
  # origin = ""
  # prefix = ""
  # target = ""

  ## Define additional aliases to map telemetry encoding paths to simple measurement names
  # [inputs.cisco_telemetry_gnmi.aliases]
  #   ifcounters = "openconfig:/interfaces/interface/state/counters"

  [[inputs.cisco_telemetry_gnmi.subscription]]
    ## Name of the measurement that will be emitted
    name = "ifcounters"

    ## Origin and path of the subscription
    ## See: https://github.com/openconfig/reference/blob/master/rpc/gnmi/gnmi-specification.md#222-paths
    ##
    ## origin usually refers to a (YANG) data model implemented by the device
    ## and path to a specific substructe inside it that should be subscribed to (similar to an XPath)
    ## YANG models can be found e.g. here: https://github.com/YangModels/yang/tree/master/vendor/cisco/xr
    origin = "openconfig-interfaces"
    path = "/interfaces/interface/state/counters"

    # Subscription mode (one of: "target_defined", "sample", "on_change") and interval
    subscription_mode = "sample"
    sample_interval = "10s"

    ## Suppress redundant transmissions when measured values are unchanged
    # suppress_redundant = false

    ## If suppression is enabled, send updates at least every X seconds anyway
    # heartbeat_interval = "60s"

Example Output

ifcounters,path=openconfig-interfaces:/interfaces/interface/state/counters,host=linux,name=MgmtEth0/RP0/CPU0/0,source=10.49.234.115 in-multicast-pkts=0i,out-multicast-pkts=0i,out-errors=0i,out-discards=0i,in-broadcast-pkts=0i,out-broadcast-pkts=0i,in-discards=0i,in-unknown-protos=0i,in-errors=0i,out-unicast-pkts=0i,in-octets=0i,out-octets=0i,last-clear="2019-05-22T16:53:21Z",in-unicast-pkts=0i 1559145777425000000
ifcounters,path=openconfig-interfaces:/interfaces/interface/state/counters,host=linux,name=GigabitEthernet0/0/0/0,source=10.49.234.115 out-multicast-pkts=0i,out-broadcast-pkts=0i,in-errors=0i,out-errors=0i,in-discards=0i,out-octets=0i,in-unknown-protos=0i,in-unicast-pkts=0i,in-octets=0i,in-multicast-pkts=0i,in-broadcast-pkts=0i,last-clear="2019-05-22T16:54:50Z",out-unicast-pkts=0i,out-discards=0i 1559145777425000000